Instructions for Use metallic FLAME COPPER & DARK BROWN
Primer
- We recommend a working temperature of approx. 20°C.
- The floor should be dust-free, clean, and even. Level out holes, unevenness, and slopes in advance with levelling compound.
- Always start with our EPOXY PRIMER (primer).
- Pour the material into a paint tray after mixing.
- Roll the material onto the desired surface with a paint roller.
- Allow the primer to dry (approx. 8-12 hours).
Main Coat
- Use our ECO epoxy resin system (resin + hardener) for the main coating.
- Divide the amount of resin (A) and hardener (B) proportionally between the two metallic colours supplied, i.e., 95% of the resin to the base colour FLAME COPPER, 5% of the resin to the highlight colour DARK BROWN.
- First, apply the base colour FLAME COPPER.
- Mix the resin (A) with the hardener (B) in a ratio of 2:1 by weight (e.g., 1kg A + 0,5kg B).
- Ideally, transfer the material to a clean mixing bucket and stir again. This will ensure that the resin (A) and hardener (B) are completely mixed together.
- Add the supplied FLAME COPPER metallic pigment to the resin/hardener mixture. We recommend a colour proportion of approx. 1.5%, e.g., 15g pigment to 1kg resin + hardener.
- Pour the material onto the floor immediately after mixing, as the product can boil up in the mixing bucket.
- Apply the material with a squeegee and foam roller flooding the entire floor. We recommend a layer thickness of 1.5mm.
- Now apply the highlight colour DARK BROWN in the same way and work the colour wet in wet into the base colour as a highlight.
- The main coating can be walked on after approx. 20 hours and is completely chemically cured after approx. 7 days.
Info: Epoxy resin is sensitive to any kind of moisture during curing (risk of amine blush formation, i.e. white patches in the top layer). For this reason, we recommend that you avoid any contact between water and the epoxy until it has cured completely (at least 7 days). For thin layers, cold temperatures (ambient, substrate, and resin temperatures below 20°C) and increased humidity, the time until the epoxy resin is fully cured may be extended.
Consumption volumes
Determine the required amount of resin needed with the help of our epoxy resin “Epoxy calculator” on this product page.
Recommended thicknesses when coating floors and other surfaces
- Overall coating (primer + main coating): approx. 1.9kg/sqm for layer thicknesses of 1.7mm
- Primer: approx. 0.2kg/sqm for layer thickness of 0.2-0.3mm
- Main layer: approx. 1.65kg/sqm for layer thicknesses of 1.5mm
Customer Service: If you have further questions, please contact us by phone, e-mail or use our WhatsApp support.
Note: Please note that due to different lighting conditions and monitors, the colours may not be uniformly displayed.
Ingredients, Security & Danger statements
A-Components (ECO) Warning: 2,2′-[(1-methylethylidene)bis(4,1-phenyleneoxymethylene)]bisoxirane Reaction mass of 2,2’-[methylenebis(4,1-phenyleneoxymethylene)]dioxirane and [2-({2-[4-(oxiran-2-ylmethoxy)benzyl]phenoxy}methyl)oxirane and [2,2’-[methylenebis(2,1-phenyleneoxymethylene)]dioxirane Oxirane, mono((C12-14-alkyloxy)methyl)derivs Causes skin irritation Causes serious eye irritation May cause an allergic skin reaction Toxic to aquatic life with long lasting effects Avoid breathing dust/fume/gas/mist/vapours/spray. Avoid release to the environment. Wear protective gloves/eye protection/face protection. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If skin irritation or rash occurs: Get medical advice/attention. Dispose of contents/container to in accordance with local/regional/international regulations. Contains epoxy constituents. May produce an allergic reaction.
B-Components (ECO) Danger: Reaction products of 3-aminomethyl-3,5,5-trimethylcyclohexylamine and 4,4’-Isopropylidenediphenol, oligomeric reaction products with 1-chloro-2,3-epoxypropane m-phenylenebis(methylamine) Salicylic acid Causes severe skin burns and eye damage. May cause an allergic skin reaction Harmful to aquatic life with long lasting effects Do not breathe dust/fume/gas/mist/vapours/spray. Wear protective gloves/eye protection/face protection. IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water [or shower]. IF INHALED: Remove person to fresh air and keep comfortable for breathing. Immediately call a POISON CENTER/doctor. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Specific treatment (see on this label). Take off contaminated clothing and wash it before reuse. Store locked up. Dispose of contents/container to in accordance with local/regional/international regulations.
EPOXY PRIMER Warning: 1,2-Benzisothiazol-3(2H)-on 2-Methyl-2H-isothiazol-3-one May cause an allergic skin reaction If medical advice is needed, have product container or label at hand. Keep out of reach of children. Avoid breathing dust/fume/gas/mist/vapours/spray. Do not get in eyes, on skin, or on clothing. Avoid release to the environment. IF ON SKIN: Wash with plenty of water and soap. Dispose of contents/container to in accordance with local/regional/international regulations.
